Search

… of blade edges at the end of each day to prevent upper jaw deflection, excessive blade wear and undue stress to … a 7/16” brass drift pin into the through-hole on the lower jaw. Tap the drift pin with a hammer until the blade is … � Do not remove the adjustment plates from the lower jaw during routine blade rotation or replacement. These …

… © 2019 Genesis Attachments, LLC GVP 07 Troubleshooting Guide Maintenance Minute 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT (743-2748)– Tel: 715.395.5252 – …

… © 2024 Genesis Attachments, LLC Bolt Torque Specifications Reference the Genesis Fastener … information. Threadlocker or anti-seize application and bolt and bolt hole cleaning beginning on page 6. Product Thread … Bolt Torque Specifications …

… - 130 3,000 - 3,400 psi 206 - 234 Bar LXP® 200 & 300 40 - 100 151 - 379 4,500 - 5,500 psi 310 - 380 BarLXP® 400 - 800 … - 60 151 - 227 4,500 - 5,500 psi 310 - 380 BarGRX 295 60 - 100 227 - 379 GRX 395 80 - 100 303 - 379 GDT 190 40 - 60 151 - 227 4,500 - 5,500 psi 310 …

… Subsea Shear (GSS) FEATURES © 2024 Genesis Attachments, LLC GSS_Metric 4/24 Rev. F Pressure … 813 813 GSS 775 6,668 889 940 GSS 2555 20,865 1,372 1,422 Genesis GSS shears are covered by a 12-month, 1,500-hour (whichever occurs first) warranty. Genesis reserves the right to continually make product …

… Subsea Shear (GSS) FEATURES © 2024 Genesis Attachments, LLC GSS 4/24 Rev. K Pressure tested to … 12,300 32 32 GSS 775 14,700 35 37 GSS 2555 46,000 54 56 Genesis GSS shears are covered by a 12-month, 1,500-hour (whichever occurs first) warranty. Genesis reserves the right to continually make product …

… Genesis Drive, Superior, WI 54880 888-SHEAR-IT (743-2748)– Tel: 715.395.5252 – genesisattachments.com This document is a … It does not replace the product safety and operator’s manuals, which must be followed by all operators and … It does not replace the product safety and operator’s manuals, which must be followed by all operators and …

… blades end-for-end Original Blade Configuration © 2019 Genesis Attachments, LLC LXP® Shear Jaw Primary & Secondary … Rotate blades to use all four cutting edges. Always use Genesis-approved blades. Blades that do not meet Genesis specifications can cause major problems, and using …

… blades end-for-end Original Blade Configuration © 2019 Genesis Attachments, LLC GXP Primary and Secondary Blade … Rotate blades to use all four cutting edges. Always use Genesis-approved blades. Blades that do not meet Genesis specifications can cause major problems, and using …

… of the boom or stick lines per settings called out in the manual. Do not use the bucket circuit or cylinder spools to … spring tension PTC valve can be purchased from the Genesis Parts Department that will mask the issue caused by high … fault/files/uploads/Rotation_Circuits_Requiring_a_CaseDrain.pdf https://www.genesisattachments.com/support/parts …

… is correct, this pressure will usually be in the 1000-1500 psi range. The bucket and auxiliary port reliefs on … on 400 class machines (over 150 gpm). Maintenance Minute 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT … Maintenance Minute © 2023 Genesis Attachments, LLC 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT …

… slow the excavator spool shift and pump initiation. Slowly reduce the flow through the flow control, just until the … be sourced through HKX, HCT or Hudco. Rotation Plumbing Case Drain Attachments requiring a case drain need to be run … excavator return filters in the tank. For complete details about case drains, see Tim’s Tech Tip - Rotation Circuits …

… GXT_Metric 8/22 Rev. S All the power in a shorter, lighter shear with a center of gravity closer to the excavator. Most … ground contact Reverse-mounted hydraulic cylinder shortens shear length and weight while protecting rod from damage … warranty. Genesis reserves the right to continually make product improvements designed to positively enhance …

… su desempeño. Patentes: genesisattachments.com/products/patents APLICACIONES – Tratamiento de Chatarra – …