Search

… of blade edges at the end of each day to prevent upper jaw deflection, excessive blade wear and undue stress to … a 7/16” brass drift pin into the through-hole on the lower jaw. Tap the drift pin with a hammer until the blade is … � Do not remove the adjustment plates from the lower jaw during routine blade rotation or replacement. These …

… blades end-for-end Original Blade Configuration © 2019 Genesis Attachments, LLC GXP Primary and Secondary Blade … Rotate blades to use all four cutting edges. Always use Genesis-approved blades. Blades that do not meet Genesis specifications can cause major problems, and using …

… of the boom or stick lines per settings called out in the manual. Do not use the bucket circuit or cylinder spools to … spring tension PTC valve can be purchased from the Genesis Parts Department that will mask the issue caused by high … fault/files/uploads/Rotation_Circuits_Requiring_a_CaseDrain.pdf https://www.genesisattachments.com/support/parts …

… is correct, this pressure will usually be in the 1000-1500 psi range. The bucket and auxiliary port reliefs on … on 400 class machines (over 150 gpm). Maintenance Minute 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT … Maintenance Minute © 2023 Genesis Attachments, LLC 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT …

… slow the excavator spool shift and pump initiation. Slowly reduce the flow through the flow control, just until the … be sourced through HKX, HCT or Hudco. Rotation Plumbing Case Drain Attachments requiring a case drain need to be run … excavator return filters in the tank. For complete details about case drains, see Tim’s Tech Tip - Rotation Circuits …

… back to approved value. ROTATION VALVE SETTINGS © 2019 Genesis Attachments, LLC GDRHRM 8/19 Rev. C 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT (743-2748)– …

… for all temperature conditions and available in a case of 10 14-ounce tubes, PN 6302601, or 40 tubes, PN …

… varies slightly depending on excavator mounting location. Genesis GSD C Grapples are covered by a 12-month, 1,500-hour … warranty. Genesis reserves the right to continually make product improvements designed to positively enhance … GSD C Spec Sheet - Metric …

… LXP® Tooth Build-Up Templates © 2021 Genesis Attachments, LLC LXPBuildupTemplates 4/21 Rev. A … far processor teeth have worn from their original shape, Genesis has created tooth build-up templates. Each template … 9102826 9102586 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT (743-2748)– Tel: 715.395.5252– …

… It does not replace the product safety and operator’s manuals, which must be followed by all operators and …

… © 2019 Genesis Attachments, LLC LXP® Cracker Jaw Maintenance Blade … Rotate blades to use all four cutting edges. Always use Genesis-approved blades. Blades that do not meet Genesis specifications can cause major problems, and using …

… required or if replacement is needed. Contact your local Genesis dealer or the Genesis Parts Department to …

… - 11 © 2024 Genesis Attachments, LLC M7_Metric 6/24 Rev. B 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT … M7 Spec Sheet - Metric …

… © 2022 Genesis Attachments, LLC LXP® Daily Maintenance Checklist … shortened maintenance intervals. Maintenance Minute 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT (743-2748)– … is a quick reference only. It does not replace the product safety and operator’s manuals, which must be followed …

… Maintenance Maintenance Minute Operating the shear below the recommended flow and/or pressure range will … performance and may damage the rotate motor. Operating the shear above the recommended flow and/or pressure range may damage the shear and its hydraulic components. HYDRAULIC REQUIREMENTS …

… genesisattachments.com © 2022 Genesis Attachments, LLC GRB_Metric 4/22 Rev. J APPLICATION – Rail Processing: 136 lb. and … Patents: genesisattachments.com/products/patents Metric Specs: Four-blade design reduces jaw wear and … GRB Spec Sheet - Metric …