Search

… of blade edges at the end of each day to prevent upper jaw deflection, excessive blade wear and undue stress to … a 7/16” brass drift pin into the through-hole on the lower jaw. Tap the drift pin with a hammer until the blade is … � Do not remove the adjustment plates from the lower jaw during routine blade rotation or replacement. These …

… blades end-for-end Original Blade Configuration © 2019 Genesis Attachments, LLC GXP Primary and Secondary Blade … Rotate blades to use all four cutting edges. Always use Genesis-approved blades. Blades that do not meet Genesis specifications can cause major problems, and using …

… of the boom or stick lines per settings called out in the manual. Do not use the bucket circuit or cylinder spools to … spring tension PTC valve can be purchased from the Genesis Parts Department that will mask the issue caused by high … fault/files/uploads/Rotation_Circuits_Requiring_a_CaseDrain.pdf https://www.genesisattachments.com/support/parts …

… is correct, this pressure will usually be in the 1000-1500 psi range. The bucket and auxiliary port reliefs on … on 400 class machines (over 150 gpm). Maintenance Minute 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT … Maintenance Minute © 2023 Genesis Attachments, LLC 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT …

… slow the excavator spool shift and pump initiation. Slowly reduce the flow through the flow control, just until the … be sourced through HKX, HCT or Hudco. Rotation Plumbing Case Drain Attachments requiring a case drain need to be run … excavator return filters in the tank. For complete details about case drains, see Tim’s Tech Tip - Rotation Circuits …

… 90 127 GXP 2500R 24,494 1,168 1,219 6,629 108 163 © 2022 Genesis Attachments, LLC GXP_Metric 4/22 Rev. J Proprietary … reach brackets are available on all non-rotating shears. Genesis GXP shears are covered by a 12-month, 1,500-hour (whichever occurs first) warranty. Genesis reserves the right to continually make product …

… an attachment in your prime mover operator’s manual, install the attachment onto your loader. 3. Lower the unit to … lines. 3. Disconnect couplers and connect them together or install dust caps and plugs to prevent contaminants from … the oil flow is within the specified range. NOTE: Always install a flow meter between the breaker inlet and outlet …

… an attachment in your prime mover operator’s manual, install the attachment onto your loader. 3. Lower the unit to … in the hydraulic lines. 3. Disconnect hydraulic lines and install dust caps and plugs to prevent contaminants from … the oil flow is within the specified range. NOTE: Always install a flow meter between the breaker inlet and outlet …

… © 2019 Genesis Attachments, LLC LXP® Cracker Jaw Maintenance Blade … Rotate blades to use all four cutting edges. Always use Genesis-approved blades. Blades that do not meet Genesis specifications can cause major problems, and using …

… 2 10 9 1 3 4 5 7 8 11 6 FEATURES © 2024 Genesis Attachments, LLC GHG_Metric 10/24 Rev. C 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT (743-2748)– … 1,448 35 - 50 * Weight does not include mounting bracket. Genesis Handling Grapples are covered by a 12-month, …

… required or if replacement is needed. Contact your local Genesis dealer or the Genesis Parts Department to …

… © 2022 Genesis Attachments, LLC LXP® Daily Maintenance Checklist … shortened maintenance intervals. Maintenance Minute 1000 Genesis Drive, Superior, WI 54880 888-SHEAR-IT (743-2748)– … is a quick reference only. It does not replace the product safety and operator’s manuals, which must be followed …

… Maintenance Maintenance Minute Operating the shear below the recommended flow and/or pressure range will … performance and may damage the rotate motor. Operating the shear above the recommended flow and/or pressure range may damage the shear and its hydraulic components. HYDRAULIC REQUIREMENTS …

… varies slightly depending on excavator mounting location. Genesis GSD C Grapples are covered by a 12-month, 1,500-hour … warranty. Genesis reserves the right to continually make product improvements designed to positively enhance … GSD C Spec Sheet - Metric …

… is a quick reference only. It does not replace the product safety and operator’s manuals, which must be followed … iles/literature/maintenance-minute/GeneralWeldingGuidelines_C.pdf …